+7 (812) 645-08-06
Plain bearings, bushings
select brand
Self-lubricated plain bearing - FluoroNyliner®
The FluoroNyliner® Bushing Bearing has a broad contact surface area that provides excellent performance...
Self-lubricated plain bearing - FluoroNyliner®
The FluoroNyliner® Bushing Bearing has a broad contact surface area that provides excellent performance...
Open plain bearing / nylon / PTFE / high-wear-resistance - 008-4 series
Made from Nylon 6.6, Aramid fibre, PFTE
Extremly high wear...
Extremly high wear...
Open plain bearing / nylon / PTFE / high-wear-resistance - 008-4 series
Made from Nylon 6.6, Aramid fibre, PFTE
Extremly high wear resistance
Suitable for soft shafts (stainless steel, ALU, plastic)
Minimum wear of friction surface
Suitable for DIN h6-H7
Technical table and fitting instructions at page 62
Extremly high wear resistance
Suitable for soft shafts (stainless steel, ALU, plastic)
Minimum wear of friction surface
Suitable for DIN h6-H7
Technical table and fitting instructions at page 62
Open plain bearing / PTFE / nylon - 103-3 series
High performance composite: Nylon 6.6 , Aramid fibre, PFTE
...
Open plain bearing / PTFE / nylon - 103-3 series
High performance composite: Nylon 6.6 , Aramid fibre, PFTE
Extremly high wear resistance
Suitable for soft shafts (stainless steel, ALU, plastic)
Minimal wear of friction surface
Low coefficient of friction
Suitable for DIN h6-H7
Technical table and fitting instructions at page 62
Extremly high wear resistance
Suitable for soft shafts (stainless steel, ALU, plastic)
Minimal wear of friction surface
Low coefficient of friction
Suitable for DIN h6-H7
Technical table and fitting instructions at page 62
Open plain bearing / nylon - 008 series
The skiffy plastic part bearings are made out of nylon-66 (PA-66). They have a natural color....
Open plain bearing / nylon - 008 series
The skiffy plastic part bearings are made out of nylon-66 (PA-66). They have a natural color. They conform to DIN h6-H7 fitting, which means that the hole diameter where the bearing is fitted is either the same size or slightly larger. Once the bearing is assembled there will be a 1 % bearing clearance in the shaft diameter. The bearings come in an assortment box 019.
Open plain bearing / PTFE / nylon / high-temperature-resistant - 008-2 series
High Performance Slide Bearings are designed for high pressure load. These bearings are...
Open plain bearing / PTFE / nylon / high-temperature-resistant - 008-2 series
High Performance Slide Bearings are designed for high pressure load. These bearings are manufactured from a special nylon-66, carbon fibre and PTFE compound. It guarantees sufficient stability even with heavy loads and high temperatures. The internal running surface is made of a special tribo-compound with good wear and friction values.
Back-up ring - 20 bar
Pressure breakers from Hoerbiger are designed to reduce pressure fluctuations for subsequent sealing rings. These efficient breakers are constructed with cast iron, PTFE,...
Back-up ring - 20 bar
Pressure breakers from Hoerbiger are designed to reduce pressure fluctuations for subsequent sealing rings. These efficient breakers are constructed with cast iron, PTFE, PEEK, bronze and other robust materials for an extended service life. Pressure breakers are typically required for pressures over 300psi (20bar) differential pressure between suction and discharge.
The pressure breaker throttles the gas pressure pulsations instead of sealing. It can restrict the gas into the case (single-acting) or in and out of the case (double-acting). Pressure above 20bar ensures the minimal load on the main packing seals and prevents the entry of dirt into the packing.
The pressure breaker throttles the gas pressure pulsations instead of sealing. It can restrict the gas into the case (single-acting) or in and out of the case (double-acting). Pressure above 20bar ensures the minimal load on the main packing seals and prevents the entry of dirt into the packing.
Back-up ring - ø 20 - 200 mm, 3 - 1 000 bar
Hoerbiger back-up rings protect non-metallic sealing rings from extruding in the clearance between the piston rod and the packing cup....
Back-up ring - ø 20 - 200 mm, 3 - 1 000 bar
Hoerbiger back-up rings protect non-metallic sealing rings from extruding in the clearance between the piston rod and the packing cup. The rings are typically constructed with cast iron or bronze. Only the end space of the packing case cup is sealed by the rings. There is a small gap in the bore hole from the piston rod.
The rings enable PTFE to be used as a sealing ring at high pressures. A broad variety of materials are available for a range of applications. Examples include natural gas or food industry.
The rings enable PTFE to be used as a sealing ring at high pressures. A broad variety of materials are available for a range of applications. Examples include natural gas or food industry.