+7 (812) 645-08-06
Generator set controllers
select brand
Generator controller - 24 V | Selco T8400 series
T8400 Series - Blackout Limiter of Littlefuse is used to monitor almost 4 generators. The T8400 Blackout Limiter makes the fast clearing of the blackout easy. It is useful for almost 4 generators with 1 unit and the 8 generators are enough for the 2 units. If the blackout occurs, the first generator...
Generator controller - 24 V | Selco T8400 series
T8400 Series - Blackout Limiter of Littlefuse is used to monitor almost 4 generators. The T8400 Blackout Limiter makes the fast clearing of the blackout easy. It is useful for almost 4 generators with 1 unit and the 8 generators are enough for the 2 units. If the blackout occurs, the first generator is required to have more than 90% voltage to close the breaker of the generator. T8400 requires 24 Vdc signal over the 15 and 16 terminals to become active and this will be an indication of the blackout.
Now all the generators will be checked and the first generator will contain more than 90 percent voltage to close the contact to the generator breaker. If the generator number 1 is the 1st generator with 90% voltage, this will take 1 second to complete the process. If the generator 2 is the first generator on the same voltage, the process requires 1.5 seconds. If the generator 3 acts as the first one, then the process requires 2 second. The addition of the second unit delays the time up to 3, 3.5, 4.5 seconds. 8 generators can be handled at a time. In case, the one of these generators has been switched on, the blackout signals 24 Vdc should be switched off.
Now all the generators will be checked and the first generator will contain more than 90 percent voltage to close the contact to the generator breaker. If the generator number 1 is the 1st generator with 90% voltage, this will take 1 second to complete the process. If the generator 2 is the first generator on the same voltage, the process requires 1.5 seconds. If the generator 3 acts as the first one, then the process requires 2 second. The addition of the second unit delays the time up to 3, 3.5, 4.5 seconds. 8 generators can be handled at a time. In case, the one of these generators has been switched on, the blackout signals 24 Vdc should be switched off.
Generator controller - Selco C6200 series
These are the FlexGen controller which are utilized for paralleling of generators with each other or with the grid. One FlexGen controller is to be installed for each of the generator in the installation ad handles all electrical control. There are two versions available which are the Basic...
Generator controller - Selco C6200 series
These are the FlexGen controller which are utilized for paralleling of generators with each other or with the grid. One FlexGen controller is to be installed for each of the generator in the installation ad handles all electrical control. There are two versions available which are the Basic and Advanced. Both of these versions have basic functions like autosynchronizing, frequency control, active load sharing, dead bus monitoring and reverse power protection. With these it also contains a reactive load sharing, voltage matching, power factor control, grid-parallel operation control, and protection against excitation loss, RoCoF (df/dt), and vector shift. FlexGen Advanced also has over-current and short-circuit protection and power management features like preferential load trip, load depending start/stop as well as large consumer control. Both models have MODBUS RTU interface which enables integration with equipment from other manufacturers, like control and monitoring from PC with a graphic SCADA interface.FlexGen is type-approved by major marine classification societies and is to be utilized for marine power management . . .
Control module for generator sets - Selco C6500 series
The C6500, manufactured by Littelfuse, is a FlexGen UI User Interface Module that is capable of providing...
Control module for generator sets - Selco C6500 series
The C6500, manufactured by Littelfuse, is a FlexGen UI User Interface Module that is capable of providing indication of measurements, alarms, alarm log and configuration of the generator module. It is an accessory intended for the FlexGen controllers. Separate LEDs provides clear indications and it also has valuable alarm logs. Furthermore, it is capable of connection using the RS232 serial link.
Controller for manual generator sets - MDM
The MDM by CRE Technology is an inexpensive microprocessor controlled unit. It is responsible for manual starting and stopping...
Controller for manual generator sets - MDM
The MDM by CRE Technology is an inexpensive microprocessor controlled unit. It is responsible for manual starting and stopping of the genset using key switch and push buttons located on the front panel. Its high-powered relay outputs enables direct interfacing with diesel gensets. The engine has an auto-shutdown when there's an alarm caused by monitored errors by the unit when the engine is running. The alarm is indicated by the first occuring LED in the group of LED displays.
Controller for manual generator sets - MDA
The MDA controller is a microprocessor controlled unit specifically designed for generator...
Controller for manual generator sets - MDA
The MDA controller is a microprocessor controlled unit specifically designed for generator sets. It functions by automatically starting and stopping the genset of an external remote start signal. This economical controller is equipped with a highly powered relay outputs that has the ability to directly work with diesel generator sets.
Controller for manual generator sets - MNS
The CRE model MNS is an affordable, microprocessor regulated section structured...
Controller for manual generator sets - MNS
The CRE model MNS is an affordable, microprocessor regulated section structured to monitor the 3-phase mains voltages, pass remote oeder to the producing set and carry out changeover of generator and mains contactors.
The genset needs to regulated by a remote start like regulation unit.
The genset needs to regulated by a remote start like regulation unit.
Automatic control panel for generator sets - TCGEN 2.0
The TCGEN 2.0 is a comprehensive AMF unit is used for a single generating set operating in standby mode.It enusres...
Automatic control panel for generator sets - TCGEN 2.0
The TCGEN 2.0 is a comprehensive AMF unit is used for a single generating set operating in standby mode.It enusres management of the generator and mains manually and automatically. The electronic module TCGEN 2.0 enables remote monitoring and control. the unit contains a programming software that saves one or more setting configurations on the PC. The series can be controlled with the push buttons located on the front panel.
Wireless generator set controller - BSD / BSD Plus
The BSD is manufactured by CRE Technology and is a wireless generator set controller...
Wireless generator set controller - BSD / BSD Plus
The BSD is manufactured by CRE Technology and is a wireless generator set controller that is ideal for use in remote management of generating sets. The unit is integrated with an alarm handler, a data logger, and a web-based data presentation function. It measures 90mm x 70mm x 58mm and it can be mounted via DIN rail.
Control panel for generator sets - QM 120
The control panel QM 120 is equipped with 4 pole circuit breaker, electronic control...
Control panel for generator sets - QM 120
The control panel QM 120 is equipped with 4 pole circuit breaker, electronic control board, key start switch, control panel box key and it has a stop button for emergency. It protects with low oil pressure and fuel level. It has a digital metering device for volt, ampere, frequency and hours. The indicator has a periodic maintenance.
Control panel for generator sets - Q5210AS
The Q5210AS control panel is designed to allow both manual and automatic operating modes...
Control panel for generator sets - Q5210AS
The Q5210AS control panel is designed to allow both manual and automatic operating modes of the generating set. The electronic module front can easily set the timers and alarms. It is equipped with an electronic control board, a circuit breaker, and an emergency stop button. The unit also features an LCD display scroll and event log view.
Automatic control panel for generator sets - Q5220AMF
The Q5220AMF control panel by BRUNO Generators permits automatic operating mode of the generating set,...
Automatic control panel for generator sets - Q5220AMF
The Q5220AMF control panel by BRUNO Generators permits automatic operating mode of the generating set, owing to the mains failure detection function. It is built in a manner that the protection system shuts down the generating set on its own, while also indicating the failure condition through an LCD display. There is a provision for acoustic alarm, event log view and and LCD display scroll as well.
Automatic control panel for generator sets - Q4400AMF
The BRUNO GENERATORS Q4400AMF series control panels contain a failure detection function, offering complete...
Automatic control panel for generator sets - Q4400AMF
The BRUNO GENERATORS Q4400AMF series control panels contain a failure detection function, offering complete automation. The protection system immediately shuts down the operation and shows the current problem via LCD display or LEDs. Also, timer and alarm options can be manually set from the control board front panel, offering flexibility and compatibility with different industrial applications.
Control panel for generator sets - 32 - 60 A | QS32ATS, QS45ATS, QS60ATS
The control panels of Bruno Generators are equipped with a battery charger, a circuit breaker, a generating set, and mains contractors....
Control panel for generator sets - 32 - 60 A | QS32ATS, QS45ATS, QS60ATS
The control panels of Bruno Generators are equipped with a battery charger, a circuit breaker, a generating set, and mains contractors. These panels also have one-phase voltmetric mains and starter control.
Automated battery charging and supervision of faults are offered by the unit. Due to their dip switches, simple positioning of parameters are featured.
The indicators of the control panels are composed of a parzial hour meter, battery voltmeter, fuel level indicator, total hour meter, and other types.
Automated battery charging and supervision of faults are offered by the unit. Due to their dip switches, simple positioning of parameters are featured.
The indicators of the control panels are composed of a parzial hour meter, battery voltmeter, fuel level indicator, total hour meter, and other types.