+7 (812) 645-08-06
Shears, Shearing machine
select brand
Marking, punching, drilling, shearing line - 72 - 110 t, min. 120 x 120 x 13 mm | HP-T series
The new HP-T series of the Ficep CNC angle line represents an excellent solution for use in demanding environmental conditions of pylon building. This...
Marking, punching, drilling, shearing line - 72 - 110 t, min. 120 x 120 x 13 mm | HP-T series
The new HP-T series of the Ficep CNC angle line represents an excellent solution for use in demanding environmental conditions of pylon building. This series offers up to 20% performance increase when compared to the previous models and can easily perform functions such as punching, drilling, shearing, programmable miter shearing of flats, notching and marking. These highly robust models feature a dedicated and user-friendly hardware and software and are equipped with a new hydraulic circuit design with higher capacities while being highly resistant to both wear and extreme weather conditions.
Angle punching-shearing machine - max. 121 t, max. 200 x 200 x 20 mm | TIPO D series
Structural steel job needs an enormous amount of plates and details intended for use as bottom plates, fin plates, gusset plates, stiffeners and several other link plates. These plates are usually bulky and approximately punched, punctured...
Angle punching-shearing machine - max. 121 t, max. 200 x 200 x 20 mm | TIPO D series
Structural steel job needs an enormous amount of plates and details intended for use as bottom plates, fin plates, gusset plates, stiffeners and several other link plates. These plates are usually bulky and approximately punched, punctured and sliced to shape at all times. Occasionally, there is a necessity to mechanically marking the part. The D8 and D4 lines create it likely to process extremely bulky plate performing a number of functions in a solitary pass. The fundamental versions contain punching ability of either 8 or 4 1100kN punching locations. This is pooled with a 2200kN revolving cut off unit for slicing equal to 510 mm broad and 25 mm solid plates. Flats glide on an inactive roller way and are stirred by a Computer numerical controlled carriage and pincher. Hydraulic vertical and horizontal clamps firmly keep the substance in the operational position. The Tipo D8 and D4 lines comprise the option to contain both angle and flats...
Marking, punching, drilling, shearing line - 44 - 110 t, min. 90 x 90 x 9 mm | A series
Angle line- solution from Ficep has provided an opportunity not only for processing angle but for flats and channels. It can be used for shearing, notching,...
Marking, punching, drilling, shearing line - 44 - 110 t, min. 90 x 90 x 9 mm | A series
Angle line- solution from Ficep has provided an opportunity not only for processing angle but for flats and channels. It can be used for shearing, notching, marking, punching, drilling, etc., with excellent precision. It is designed to suit the requirements of both the medium and smaller steel companies. It is highly flexible and can be operated easily. The machine can be operated even by a non specialized staff due to it's simplicity which caters to the needs of the small companies with less number of employees. As per the needs of the customer, it can be configured to match diverse applications.
Marking, punching, drilling, shearing line - 72 - 110 t, min. 160 x 160 x 16 mm | L-T series
Using the traditional cutting technique called "the FICEP double cut shear", the Ficep CNC angle line model L gives the ability to process long bracing, diagonals and webs. This shearing...
Marking, punching, drilling, shearing line - 72 - 110 t, min. 160 x 160 x 16 mm | L-T series
Using the traditional cutting technique called "the FICEP double cut shear", the Ficep CNC angle line model L gives the ability to process long bracing, diagonals and webs. This shearing technology features punching, drilling, shearing, notching and marking processes. The machine reduces the effort required in every operation as it can reduce cycle time and can attain 20% more performance while making the investment more profitable.
Meanwhile, the Ficep L can be customized in different ways to get the different operations in a single pass, thus enabling the customer to configure a line that can be made to attain the requirements set by the company. The lines enter as a raw materials and and exit as a punched and drilled products.
Meanwhile, the Ficep L can be customized in different ways to get the different operations in a single pass, thus enabling the customer to configure a line that can be made to attain the requirements set by the company. The lines enter as a raw materials and and exit as a punched and drilled products.
Marking, punching, drilling, shearing line - 350 x 350 x 40 mm | HP 35 T
The Angle Drill Line serves as a solution for milling, drilling, scribing and slotting purposes. Its angle drilling can also be merged with disc and carbide disc...
Marking, punching, drilling, shearing line - 350 x 350 x 40 mm | HP 35 T
The Angle Drill Line serves as a solution for milling, drilling, scribing and slotting purposes. Its angle drilling can also be merged with disc and carbide disc marking sawing, and various automatic handling device. It has a automatic changer and a carbide drilling feature. This enables the machine for easy installation and eliminating the need for set-up procedures.
The HP lines can also be tailored and configured in different sizes and capacity allowing it to deliver processing in a single pass. These lines are real working cells where an angle goes into as a raw item and departs as a integration of drilled parts.
The HP lines can also be tailored and configured in different sizes and capacity allowing it to deliver processing in a single pass. These lines are real working cells where an angle goes into as a raw item and departs as a integration of drilled parts.
Pneumatic shear - 4 200 spm | 7802SA
The Ingersoll Rand 7812G is a heavy duty air shear, particularly designed in cutting...
Pneumatic shear - 4 200 spm | 7802SA
The Ingersoll Rand 7812G is a heavy duty air shear, particularly designed in cutting rolled steel of up to 20 gauge without chipping. This innovative product features durable, sturdy cutting blades, a variable speed controller, an ergonomic grip, and a diffused handle exhaust which blows air away from your work.
Guillotine shear / electro-hydraulic - 3 100 mm | B-shear
The primary reason for the uniqueness of this competitively priced shear is its unmatched hybrid drive. The powerful hydraulics are governed by superior electronics. The SafanDarley B-Shear utilized substantially less oil than other hydraulic shears in its segment. The servo electronic...
Guillotine shear / electro-hydraulic - 3 100 mm | B-shear
The primary reason for the uniqueness of this competitively priced shear is its unmatched hybrid drive. The powerful hydraulics are governed by superior electronics. The SafanDarley B-Shear utilized substantially less oil than other hydraulic shears in its segment. The servo electronic motor only functions when the cutting beam is moving, which results in substantial energy savings and also a low noise energy cycle.
The SafanDarley B-Shear offers the exact same cutting method as the SafanDarley B-Shear except with a single blade variant with less accessories and just a handful of optional features. The specifications of the SafanDarley B-Shear include a cutting capacity of sheet thickness 6 mm, cutting length 3100 mm, drive complete servo-electronic motor and hydraulic pump, 22 liter oil tank, SafanDarley TS200 touch screen control that is appointed with CNC programming of cutting programs, torsion resistant cutting of smaller strips, CNC dominated back gauge, available in standard with pneumatic sheet-holding device and safety specifications in compliance with the European Machinery Directive.
The SafanDarley B-Shear offers the exact same cutting method as the SafanDarley B-Shear except with a single blade variant with less accessories and just a handful of optional features. The specifications of the SafanDarley B-Shear include a cutting capacity of sheet thickness 6 mm, cutting length 3100 mm, drive complete servo-electronic motor and hydraulic pump, 22 liter oil tank, SafanDarley TS200 touch screen control that is appointed with CNC programming of cutting programs, torsion resistant cutting of smaller strips, CNC dominated back gauge, available in standard with pneumatic sheet-holding device and safety specifications in compliance with the European Machinery Directive.
Guillotine shear / electro-hydraulic - 2 050 - 6 500 mm | M-shear
SafanDarley M-Shear multifunctional shears stand out due to their unique hybrid drive. Advanced electronics is used for controlling the strong hydraulics.
In comparison to hydraulic shears, very little oil is consumed by the M-Shear. Significant savings in energy as well are lower wear are provided due...
In comparison to hydraulic shears, very little oil is consumed by the M-Shear. Significant savings in energy as well are lower wear are provided due...
Guillotine shear / electro-hydraulic - 2 050 - 6 500 mm | M-shear
SafanDarley M-Shear multifunctional shears stand out due to their unique hybrid drive. Advanced electronics is used for controlling the strong hydraulics.
In comparison to hydraulic shears, very little oil is consumed by the M-Shear. Significant savings in energy as well are lower wear are provided due to the servo-electronic motor running only with the movement of the cutting beam. M-Shear also provides a cutting cycle with minimum noise. It is driven by servo-electronic motor and hydraulic pump. The oil tank is only 22 liters.
M-Shear includes the SafanDarley TS200 touch screen control. Cutting can programmed with CNC. Cutting angle and stroke length can be set automatically. The narrow strips can be cut without any torsion. It has a backgauge, which is controlled by CNC. It features safety provisions as per the European Machinery Directive.
M-Shear provides optional devices for holding pneumatic sheet, supporting the sheet and a system called Return-to-Sender. Customers can choose from over 20 versions. The cutting capacity in terms of sheet thickness is available in 4 mm, 6 mm, 8 mm, 10 mm, 13 mm, and 16 mm. Options for working length are 2050 mm, 2550 mm, 3100 mm, 4300 mm, 6100 mm, and 6500 mm.
In comparison to hydraulic shears, very little oil is consumed by the M-Shear. Significant savings in energy as well are lower wear are provided due to the servo-electronic motor running only with the movement of the cutting beam. M-Shear also provides a cutting cycle with minimum noise. It is driven by servo-electronic motor and hydraulic pump. The oil tank is only 22 liters.
M-Shear includes the SafanDarley TS200 touch screen control. Cutting can programmed with CNC. Cutting angle and stroke length can be set automatically. The narrow strips can be cut without any torsion. It has a backgauge, which is controlled by CNC. It features safety provisions as per the European Machinery Directive.
M-Shear provides optional devices for holding pneumatic sheet, supporting the sheet and a system called Return-to-Sender. Customers can choose from over 20 versions. The cutting capacity in terms of sheet thickness is available in 4 mm, 6 mm, 8 mm, 10 mm, 13 mm, and 16 mm. Options for working length are 2050 mm, 2550 mm, 3100 mm, 4300 mm, 6100 mm, and 6500 mm.
Guillotine shear / electric - 1 250 - 6 050 mm | GS-shear
This multi purpose and heavy duty shear outweighs in sustainable process dependability. One of its unique features is the oscillating cutting beam with corresponding clearance angle, which results in an increased life term of the blades. Furthermore, this machine has no other moving components that...
Guillotine shear / electric - 1 250 - 6 050 mm | GS-shear
This multi purpose and heavy duty shear outweighs in sustainable process dependability. One of its unique features is the oscillating cutting beam with corresponding clearance angle, which results in an increased life term of the blades. Furthermore, this machine has no other moving components that can be affected by wear. Extended lifetime, superior precision and reduced maintenance collectively are displayed in the SafanDarley GS-Shear. There are over 20 execution types to choose from and cutting capacity plate thickness of 4 mm - 6 mm 8 mm 10 mm 13 mm 16 mm 20 mm 25 mm, and 1250 mm 3050 mm 4050 mm 6050 mm working lengths.
This oscillating cutting beam features a supreme static cutting angle and can be electrically installed with a power source of AC current supply 3/N/PE 50 Hz 400-230 V. The touchscreen controller is complete with a 15" TFT didplay and the unit can be moved to the middle of the shear CNC-governed cutting gap adjustment CNC back gauge. It is driven by an AC servo motor and is able to reach 1000 mm. Other features of this machine include double sided retractable with electrical interlock and finger protection down holder fence.
This oscillating cutting beam features a supreme static cutting angle and can be electrically installed with a power source of AC current supply 3/N/PE 50 Hz 400-230 V. The touchscreen controller is complete with a 15" TFT didplay and the unit can be moved to the middle of the shear CNC-governed cutting gap adjustment CNC back gauge. It is driven by an AC servo motor and is able to reach 1000 mm. Other features of this machine include double sided retractable with electrical interlock and finger protection down holder fence.