+7 (812) 645-08-06

Mechanical presses

select brand

Punch press / mechanical - 35 - 250 t | NC1 series

The first in AIDA'S NC series, the NC1 are single point gap frame presses, equipped with the latest hydraulic overload protection system or HOLP that provides high response...

Punch press / mechanical - 35 - 250 t | NC1 series

The first in AIDA'S NC series, the NC1 are single point gap frame presses, equipped with the latest hydraulic overload protection system or HOLP that provides high response time and tonnage capability of 60-100%, a highly durable wet clutch that contributes to the machine's cost efficiency, and a 6-point slide adjustment guide, all encased in a welded steel frame housing with a built-in cast steel bolster that increases this machine's accuracy.

It is integrated with an advanced control system easily programmed to set the parameters for easy operation. A lubrication system is also incorporated to provide oil lube to the shaft and bearings.

Punch press / mechanical - 110 - 250 t | NC2 series

The NC2 by AIDA are mechanical gap frame stamping presses, equipped with the latest hydraulic overload protection system or HOLP that provides high response time and tonnage...

Punch press / mechanical - 110 - 250 t | NC2 series

The NC2 by AIDA are mechanical gap frame stamping presses, equipped with the latest hydraulic overload protection system or HOLP that provides high response time and tonnage capability of 60-100%, highly durable cutting gears, and a slide adjustment, all encased in a welded steel frame housing with built in cast steel bolster that increases this machine's accuracy.

It is ideally used in the manufacturing industry particularly in die cast/molding. Its also been fitted with wet clutch, electric brake for the sliding motor, and a lubrication system for the shaft and rear crank bearings. Its easy to operate with low cost of maintenance.

Mechanical press / C-frame - 80 - 250 t | DSF-C1 series

The DSF-C1 is a gap frame servo press series with a large capacity range and programmable stoke profiles. It is offered by AIDA, a direct drive servo technology leader...

Mechanical press / C-frame - 80 - 250 t | DSF-C1 series

The DSF-C1 is a gap frame servo press series with a large capacity range and programmable stoke profiles. It is offered by AIDA, a direct drive servo technology leader that is currently offering the first important change in the meta-forming industry in over three decades. The high-torque and low-RPM servo motors offered by this brand are specifically built for stamping press applications.

This press model features ServoPro technology and has the same energy characteristics and torque as a conventional mechanical press. Advantages include a manual step feed, improved press performance and a variety of specifications and options.

Mechanical press / straight-side - 80 - 200 t | NS1

The AIDA NS1 straightside press represents a design well suited for drawing, bending, and compression applications due to it's optimum...

Mechanical press / straight-side - 80 - 200 t | NS1

The AIDA NS1 straightside press represents a design well suited for drawing, bending, and compression applications due to it's optimum link motion. This design owes it's high performance capabilities to a range of features such as a straightside frame construction for added accuracy and lower deflection, centered slide guides in full length, lubrication system that uses forced recycling and AIDA's patented hydraulic overload protection. In addition the NS1 is available in two variants, the crank motion model and a link motion version.

Mechanical press / straight-side - 110 - 300 t | NS2

The AIDA NS2 is suitable for operations involving crank and link motion prototypes. Its link motion feature expands the range of metal-forming possibilities to include difficult-to-form materials, prolong service life and minimize noise.

The device conducts its operation through the slide guides as it enables good performance and strong resistance against eccentric loads. It is equipped with a unitized straightside frame to provide low fame extension which is tightened through a tie rod.

It runs through a hydraulic overload protection system and HOLP motor. It has an automatic lubrication in the crank bearing and slide guides, thus, enhances the Bottom Dead Center. Through this, it reduces the thermal expansion of the frame and acquiring 10% of the SPM.

Mechanical press / hinged type connecting rod - 6 300 - 32 000 kN

The production of advanced dies involves fine quality materials by the feed unit of the coil string. Just one stroke...

Mechanical press / hinged type connecting rod - 6 300 - 32 000 kN

The production of advanced dies involves fine quality materials by the feed unit of the coil string. Just one stroke is required to segregate the crafted parts from the coil string.

Maximum stroking speed up to 60 spm can be achieved using ProgDie presses from Schuler as drive forces ranging from 6,300 to 32,000 kN. It also offers unconventional drive forces from 6,300 to 25,000 kN and ensures a 100% precision using top-class rigidity of the press.

Transfer press / mechanical - 10 000 - 35 000 kN | TWIN SERVO

Schuler has set new standards in servo technology with its latest TwinServo technology and brought radical changes to the press world. The first transfer press developed by the Schulers Forming Center in Erfurt, featuring TwinServo technology, can handle 16,000 kN and is completely automated using Schuler-designed parts.

Two separate torque motors are included in the press bed, with each having a capacity of 503 kilowatts. The unique arrangement of the two decentralized drives ensures there's adequate room for the drawing cushions and scrap chutes. The press enables electronic synchronization of the drives.

The TwinServo Technology is suitable for transfer and ProgDie presses with capacities in the range of 10,000 to 35,000 kN.

The press offers bed length between 5m and 8m and width in the range of 2.2m and 3m. When compared to traditional models, TwinServo presses have a much lower height of approximate 6m. Also they require 30% less space.

Forming press / transfer / mechanical / axis - 6 300 - 50 000 kN

The mechanical transfer presses in this product series come with four-point suspension, featuring a large opening in the uprights. As a consequence, the user will benefit from the largest possible die space. Next, the transfer presses with link drive are available with capacities between 6,300 and 50,000kN, while the eccentric drive comes with 6,300 to 25,000kN.

The manufacturer also offers eccentric presses with one-, two- or three-point suspension and, depending on the requirements of the application, users can also opt for one or more slides. As a supplier of forming technologies, the manufacturer offers auxiliary equipment for the transfer presses as well, including destacker/blankloader, tri-axis transfer systems and coil lines. In addition, the line concepts are delivered for a high degree of flexibility, cost-effectiveness and production reliability.

Forming press / mechanical / multi-slide - 2 500 - 60 000 kN

The significant difference between the traditional multi-station presses and the transfer presses is that solitary forming stations can be attuned individually....

Forming press / mechanical / multi-slide - 2 500 - 60 000 kN

The significant difference between the traditional multi-station presses and the transfer presses is that solitary forming stations can be attuned individually. Another major difference is the outwardly situated blanking slide for the incorporated manufacture of blanks. Multi-station presses may be one-slide or many-slide in plan and are obtainable in different capacities ranging from 2.500 kN to 60.000 kN. Component transfer is offered on demand by automatic or electric rail transport systems. It also features an externally located blanking slide for integrated production of blanks.

Mechanical press line / high-speed / with transfer system - 6 300 - 25 000 kN

Schuler Crossbar Feeder has been specifically designed to make mechanical press lines more cost efficient. The use of crossbar feeder automation in a press line enables direct transportation of panels from one press to another without any stations in between. It also allows repositioning of components before they are placed into the die.

Crossbar feeder significantly increases the production rate, as high as 15 strokes per minute, as opposed to mechanical press lines with robot or feeder automation. The crossbar feeder can also be used in mechanical with high speeds to load the introductory station press and in the last station for unloading the finished parts.

The crossbar feeder provides seven degrees of motion freedom. The distances between presses are shorter. For each transfer from one press to another, it requires only a single gripper tool. The changing over of dies and tooling can be done quickly.

Mechanical press / C-frame - max. 40 x 120 mm | 6T

Meet with EC rules ( 3 CE type notifications)
- Quick...

Mechanical press / C-frame - max. 40 x 120 mm | 6T

Meet with EC rules ( 3 CE type notifications)
- Quick stroke and swivel screw adjustment
- Strength/reliability of the press and its components
- More safety for increased productivity (screen - guards)

Mechanical press / C-frame - max. 75 x 180 mm | 15T

EMG Presses' Mechanical Presses are designed and manufactured to comply with international...

Mechanical press / C-frame - max. 75 x 180 mm | 15T

EMG Presses' Mechanical Presses are designed and manufactured to comply with international EC standards (3 CE-type notifications). These units are built with integrated screen guards to enable enhanced levels of safety, and in turn, productivity. They showcase quick stroke and swivel screw modification functions, and comprehensive components and overall designs.

Mechanical press / C-frame - max. 75 x 210 mm | 25T

Emg Presses manufactures a wide variety of automated presses that complies to EC...

Mechanical press / C-frame - max. 75 x 210 mm | 25T

Emg Presses manufactures a wide variety of automated presses that complies to EC standards. The models have a rapid stroke and swivel screw configuration functions, and are integrated with a screen and guards as a means of safety. Both the presses and their components are durable and provide reliable performance.

Mechanical press / C-frame - max. 100 x 220 mm | 45T

The 45T model is manufactured by EMG Presses, and is a mechanical press that...

Mechanical press / C-frame - max. 100 x 220 mm | 45T

The 45T model is manufactured by EMG Presses, and is a mechanical press that complies with the EC standards of 3 CE type notifications. It has a fast stroke and swivel screw adjustment, which has a strength and reliability. It also has a variable stroke of 6 to 100 mm, which has a swan-neck depth of 220 mm.