+7 (812) 645-08-06
Weld and glue fittings
select brand
Weld fitting / stainless steel
AWH Bends DIN 11852 are made from AISI 304, 304L (1.4301 / 1.4307) or AISI 316L (1.4404) materials.. Other base materials are available...
Weld fitting / stainless steel
AWH Bends DIN 11852 are made from AISI 304, 304L (1.4301 / 1.4307) or AISI 316L (1.4404) materials.. Other base materials are available...
Weld fitting / stainless steel - 45°
The Bent fittings from AWH are compliant to DIN 11852. They have been engineered from...
Weld fitting / stainless steel - 45°
The Bent fittings from AWH are compliant to DIN 11852. They have been engineered from high-grade materials with the advanced manufacturing processes and systems. These products are made to follow standards in quality, cleanliness, and traceability. Moreover, the components used may come with a WAZ 3.1 DIN EN 10204 certification.
Weld fitting / T / stainless steel
Solutions for the food and drinks industries are produced by AWH through their wide range of shaped pipe fittings. These have been formed in Western...
Weld fitting / T / stainless steel
Solutions for the food and drinks industries are produced by AWH through their wide range of shaped pipe fittings. These have been formed in Western...
Weld fitting / cross / stainless steel
AWH's Cross Fittings come in various configurations. These include short crosses, long crosses,...
Weld fitting / cross / stainless steel
AWH's Cross Fittings come in various configurations. These include short crosses, long crosses, union part-integrated long crosses, and both reduced variations of long and short crosses. They have been all been manufactured out of materials and technologies that comply with international fitting standards. All these components comply with WAZ 3.1 DIN EN 10204 requirements.
Weld fitting / stainless steel - -1 - 7 bar
The AWH-Connect is sanitary connection for use in vessels. It is specifically engineered to meet the specifications of the biotechnological, pharmaceutical and food industry....
Weld fitting / stainless steel - -1 - 7 bar
The AWH-Connect is sanitary connection for use in vessels. It is specifically engineered to meet the specifications of the biotechnological, pharmaceutical and food industry. Replacing traditional clamp connections, the AWH-Connect eradicates dead space within the vessels and integrates the usual seal of a clamp connection specifically DIN 32676 or ASME-BPE. A block flange that is welded into the wall of the vessel enables a piece of the vessel flush to be attached to the wall therefore moving it closer to the product and cancelling negative space. Minimal maintenance and sterilization of the CIP/SIP vessels is one of the many features of this equipment.
Elbow fitting / brass - 3/16 - 1/16" | MHL
Beswick barb to barb tubing union has an elbow fitting supported by fixed position tubing. It is suitable for joining two tubes or hoses of similar inside diameter. It provides a maximum pressure rating of 100 psig if used...
Elbow fitting / brass - 3/16 - 1/16" | MHL
Beswick barb to barb tubing union has an elbow fitting supported by fixed position tubing. It is suitable for joining two tubes or hoses of similar inside diameter. It provides a maximum pressure rating of 100 psig if used with suitably sized polyurethane tubing. With a clamp fastened, the tubing's burst pressure is the limiting factor.
The material used is 303 stainless steel, ENP Brass, 316 stainless steel, and brass. The tubing is pushed easily on to the fitting by hand with Beswick's proprietary "line contact" barb with single edge. At the same time, it still provides high holding power. Also a leak tight connection is assured at the tubing interface.
It should be noted the recommended tube ID is for polyurethane or vinyl tubing. Customers planning to use a different tubing material need to consult factory.
The material used is 303 stainless steel, ENP Brass, 316 stainless steel, and brass. The tubing is pushed easily on to the fitting by hand with Beswick's proprietary "line contact" barb with single edge. At the same time, it still provides high holding power. Also a leak tight connection is assured at the tubing interface.
It should be noted the recommended tube ID is for polyurethane or vinyl tubing. Customers planning to use a different tubing material need to consult factory.