+7 (812) 645-08-06
Current measuring devices
select brand
AC current transducer - 5 - 100 A | MCOEAQ series
These transducers, with integrated current transformer, are suitable to measure the rms
value of currents...
value of currents...
AC current transducer - 5 - 100 A | MCOEAQ series
These transducers, with integrated current transformer, are suitable to measure the rms
value of currents with sinusoidal undistorted waveforms or, for the TRMS types only, also
with distorted waveforms; in this case the additional error is 0.5% for crest factor < 3 and
1% for crest factor < 7. The outputs are load independent d.c. current or voltage, proportional
to the input variable.
value of currents with sinusoidal undistorted waveforms or, for the TRMS types only, also
with distorted waveforms; in this case the additional error is 0.5% for crest factor < 3 and
1% for crest factor < 7. The outputs are load independent d.c. current or voltage, proportional
to the input variable.
Leakage current tester - 50uA - 50mA | ST5540
The ST5540 is a leak current tester from Hioki that conducts electrical safety test to ensure the safe operation of electrical products. This device measures insulation resistance, withstand voltage, ground...
Leakage current tester - 50uA - 50mA | ST5540
The ST5540 is a leak current tester from Hioki that conducts electrical safety test to ensure the safe operation of electrical products. This device measures insulation resistance, withstand voltage, ground resistance, and leakage current. It adheres to the standards of medical and non-medical electrical equipment testing and is suitable for leakage current in various types of electrical products like computers. Its support for rated currents up to 20 A gives the instrument more than adequate capability for testing products designed to comply with new standards.
This device comprises of measurement networks that simulate the human body and a high-frequency voltmeter. This makes it capable of switching power supply polarities and making measurements under simulated fault conditions in equipment under test.
This device comprises of measurement networks that simulate the human body and a high-frequency voltmeter. This makes it capable of switching power supply polarities and making measurements under simulated fault conditions in equipment under test.
Leakage current tester - 50 μA - 50 mA | ST5541
The ST5541 Leakage Current HiTester -HTI can be used in various leak current measurement applications. It is made...
Leakage current tester - 50 μA - 50 mA | ST5541
The ST5541 Leakage Current HiTester -HTI can be used in various leak current measurement applications. It is made to conform to different standards and regulation. A continuous polarity switching function is integrated. Through this feature, a minimized cycle time is made possible. The equipment is built with touch panel feature that enables an interactive operation. It is manufactured with an ability to support rated currents up to 20 A.
Clamp ammeter - 1 mA - 1000 A | 3293-50
The 3293-50, manufactured by Hioki, is a digital clamp meter that is designed to measure the...
Clamp ammeter - 1 mA - 1000 A | 3293-50
The 3293-50, manufactured by Hioki, is a digital clamp meter that is designed to measure the leakage current and load on a single device. It has a flip cam design, 6 ranges, and a bar graph display which allows the operator to easily read measured values in various heights. Furthermore, the clamp meter is capable of measuring 1 mA to 1000 A with high accuracy.
Clamp ammeter - max. 200 A | 3283
HIOKI 3283 Clamp On Leak HiTESTER formonitoring leak current fluctuations. It has a wide bandwidth in...
Clamp ammeter - max. 200 A | 3283
HIOKI 3283 Clamp On Leak HiTESTER formonitoring leak current fluctuations. It has a wide bandwidth in...
DC clamp ammeter / AC - max. 2000 A | 3290/ 3290-10
The FMI Series manufactured by HIOKI is a 3290 Clamp On AC/DC Meter. It functions as a measuring device with a unit...
DC clamp ammeter / AC - max. 2000 A | 3290/ 3290-10
The FMI Series manufactured by HIOKI is a 3290 Clamp On AC/DC Meter. It functions as a measuring device with a unit of DC or 1Hz. This device is available with up to three sensors that has the capacity to measure ranging from 100A up to 2000A.
Moreover, the FMI Clamp On AC/DC Meter has a wide range of measurement methods that are the DC used for the battery measurements, AC+DC RMS for the current distortions and the PEAK or peak value measurements.
Moreover, the FMI Clamp On AC/DC Meter has a wide range of measurement methods that are the DC used for the battery measurements, AC+DC RMS for the current distortions and the PEAK or peak value measurements.
AC clamp ammeter - max. 600 A | HT4010
The HT4010 model is manufactured by HT Instruments, and is a clamp meter that...
AC clamp ammeter - max. 600 A | HT4010
The HT4010 model is manufactured by HT Instruments, and is a clamp meter that measures AC current up to 600 A. It has an AC/DC voltage up to 600 V with resistance and continuity test. It is also intended with a built-in sensor for AC voltage detection without contact signaled by a red LED and acoustic buzzer.
Clamp ammeter - max. 400 A AC | HT4012
The HT4012 is an amperometric clamp manufactured by HT Instruments. It is fit for use under domestic and industrial...
Clamp ammeter - max. 400 A AC | HT4012
The HT4012 is an amperometric clamp manufactured by HT Instruments. It is fit for use under domestic and industrial environments, due to its compliance with the IEC/EN61010-1, CAT III 600V.
The clamp measures a maximum of 400A for AC current measurement, as well as AC/DC voltage measurement. The device is equipped with a rubber cap mounted on patented jaws, which allows holding test leads with one hand while measuring.
The clamp measures a maximum of 400A for AC current measurement, as well as AC/DC voltage measurement. The device is equipped with a rubber cap mounted on patented jaws, which allows holding test leads with one hand while measuring.
AC clamp ammeter / autorange - max. 400 A AC | HT4014
This HTC 4014 clamp meter is used for measuring AC currents that can reach up to 400A full in autorange. It can...
AC clamp ammeter / autorange - max. 400 A AC | HT4014
This HTC 4014 clamp meter is used for measuring AC currents that can reach up to 400A full in autorange. It can also be utilized in measuring AC/DC voltage, resistance, frequency, and continuity. It is equipped with a rubber cap to be mounted on the jaws, and is capable of holding test leads while measuring. The HTC 4014 is provided with a 3 3/4 LCD display with backlight, and an analog bar graph that allows convenient readability.
Clamp ammeter - max. 200 A AC, 750/1 000 V AC/DC | HT7011
The HT7011 by HT is an ammeter clamp designed for AC current measurements which are up to 200 A. The unit uses an open clamp technology wherein it is designed for cable that easily...
Clamp ammeter - max. 200 A AC, 750/1 000 V AC/DC | HT7011
The HT7011 by HT is an ammeter clamp designed for AC current measurements which are up to 200 A. The unit uses an open clamp technology wherein it is designed for cable that easily fits with its relative section located on the top of the meter. With this technology, it permits a performance which is quick and flexible to most current measurements. The clamp is integrated with a sensor for detecting the presence of voltage even without direct contact on its point test. Also, it can perform DC/AC voltage measurements which uses a double insulation CAT IV 600V and CAT III 1000V that is based in EN61010-1 safety standard. Plus, it is equipped with a buzzer and diode test for operation continuity measurements.
AC clamp ammeter / true RMS / DC - max. 600 A | HT7015
The HT7015 is a professional clamp that is made to measure alternate current which ranges up to 600 A to attain safety CAT III 600 V depending...
AC clamp ammeter / true RMS / DC - max. 600 A | HT7015
The HT7015 is a professional clamp that is made to measure alternate current which ranges up to 600 A to attain safety CAT III 600 V depending on the IEC/EN61010-1 standard.
The clamp has a huge LCD display with a backlight and a bar graph providing ease of reading in strict environments. Each of its function can be done through the use of a rotary selector at 8 positions, involving the key to enable data HOLD function. It also has an auto-power off function to preserve the inner battery. It can clamp a conductor within the maximum size of 35 mm.
The clamp has a huge LCD display with a backlight and a bar graph providing ease of reading in strict environments. Each of its function can be done through the use of a rotary selector at 8 positions, involving the key to enable data HOLD function. It also has an auto-power off function to preserve the inner battery. It can clamp a conductor within the maximum size of 35 mm.