+7 (812) 645-08-06
Magnetic drive centrifugal pumps
select brand
Centrifugal pump / magnetic-drive - DN 32÷100 - 200 m³/h - 16 bar | NDM
The NDM series of single stage centrifugal magnetic drive pumps. They are according to the ISO 2858 Standards. It has a foot mounting along with a single vault casing which has a flanged suction end and a discharge...
Centrifugal pump / magnetic-drive - DN 32÷100 - 200 m³/h - 16 bar | NDM
The NDM series of single stage centrifugal magnetic drive pumps. They are according to the ISO 2858 Standards. It has a foot mounting along with a single vault casing which has a flanged suction end and a discharge top.
It is shaft supported by oil lubricated ball bearings.There is also a close coupled one that is available.
It has cobalt samarium magnets standards which are synchronous magnets couplings that prevent it from slipping. The bearing are made of silicon carbine to be temperature proof.
The NDM series pumps redesigned in such a way that minimal spares need to be used lowering the maintenance cost.
It has a back pull out design for when the pump is equipped with a spacer type of coupling. The complete rotor can be removed from the pump casing without affecting the piuping or the motor.
It is shaft supported by oil lubricated ball bearings.There is also a close coupled one that is available.
It has cobalt samarium magnets standards which are synchronous magnets couplings that prevent it from slipping. The bearing are made of silicon carbine to be temperature proof.
The NDM series pumps redesigned in such a way that minimal spares need to be used lowering the maintenance cost.
It has a back pull out design for when the pump is equipped with a spacer type of coupling. The complete rotor can be removed from the pump casing without affecting the piuping or the motor.
Centrifugal pump / magnetic-drive - 3/4"÷1"½ - 30 m³/h - 16 Bar | SDM
Pumps of SDM series are single-stage centrifugal magnetic drive pumps. The pumps are developed for handling acids, solvents, alkalis, flammable and other aggressive...
Centrifugal pump / magnetic-drive - 3/4"÷1"½ - 30 m³/h - 16 Bar | SDM
Pumps of SDM series are single-stage centrifugal magnetic drive pumps. The pumps are developed for handling acids, solvents, alkalis, flammable and other aggressive chemicals. They are applicable for light-duty and safe operation, to guarantee low maintenance charges and long life service. They may also be used for all industries where leak proof applications are needed.
The magnet couplings Samarium Cobalt assure safe functioning and with optimum specific gravity liquids.
The SDM series features silent operations. They showcase high-quality effectiveness in a wide range of pumping duties.
The magnet couplings Samarium Cobalt assure safe functioning and with optimum specific gravity liquids.
The SDM series features silent operations. They showcase high-quality effectiveness in a wide range of pumping duties.
Centrifugal pump / magnetic-drive - DN 32÷80 - 140m³/h - 10 Bar | PCM
The PCM series offers a wide array of magnetic-drive centrifugal pumps enclosed in thick housing fabricated from solid blocks of Polyvinylidene fluoride and Polypropylene material. These pumps consists of metallic...
Centrifugal pump / magnetic-drive - DN 32÷80 - 140m³/h - 10 Bar | PCM
The PCM series offers a wide array of magnetic-drive centrifugal pumps enclosed in thick housing fabricated from solid blocks of Polyvinylidene fluoride and Polypropylene material. These pumps consists of metallic components that do not come in contact with the media pumped. The PCM and PCM-SP versions are equipped with magnetic couplings that are characterized by their miniature structure and are also close coupled. They are integrated with off the shelf motors engineered to meet IEC and NEMA standards. All pumps are incorporated with shaft and bearings that are made from either 99.7% pure Alumina Oxide or Silicone Carbide which provides maximum chemical susceptibility. They are installed with O-rings that are made from various materials which include EPDM rubber, Viton fluoroelastomer or Fluorinated ethylene propylene material.
Centrifugal pump / process / magnetic-drive - API 685
API 685 Seal-leas MDP Pump form GRUPPO ATURIA is designed to meet critical nozzle loading and working pressure requirements as...
Centrifugal pump / process / magnetic-drive - API 685
API 685 Seal-leas MDP Pump form GRUPPO ATURIA is designed to meet critical nozzle loading and working pressure requirements as per API 685 standards. Suitable for applications in petroleum industry these pumps have over designed pump casings and base plates with heavy-duty containment housing for optimum safety. Its external lubrication systems maintains highest pressure differential; allowing for deadheading and flow or pressure monitoring with Dual back-pull-out (access hydraulic end or power frame).
Centrifugal pump / side-channel / magnetic-drive - max. 35 m³/h, max. 40 bar | CEH-X/CEH series
These are the CEH-X/CEH pumps which are highly advanced. They have a segmental type construction with open vane wheel impellers. The designing of this pump is a centrifugal combined system like design. This combination pump can be is suited with a centrifugal stage in serial...
Centrifugal pump / side-channel / magnetic-drive - max. 35 m³/h, max. 40 bar | CEH-X/CEH series
These are the CEH-X/CEH pumps which are highly advanced. They have a segmental type construction with open vane wheel impellers. The designing of this pump is a centrifugal combined system like design. This combination pump can be is suited with a centrifugal stage in serial connection before the side channel stages to gain a better NPSH.
It has a number of applications such as : This CEH-X/CEH pumps can be used to pump problem free clean liquids and fluids at not good suction side conditions. They can also be used for positive suction heads which are below 0.5 m. The CEH is highly recommended for use because it has different material possibilities with uniform dimensions and performance characteristics as well as the standard exchangeable components. It is highly suitable to be used in pharmaceutical, chemical or petrochemical market and in the plastic or oil industry as well. Due to its low NPSH as well as the positive suction head, it is highly suited for pumping of liquefied gasses and liquids under vapor pressure like condensate, refrigerant, boiler feed water . . .
It has a number of applications such as : This CEH-X/CEH pumps can be used to pump problem free clean liquids and fluids at not good suction side conditions. They can also be used for positive suction heads which are below 0.5 m. The CEH is highly recommended for use because it has different material possibilities with uniform dimensions and performance characteristics as well as the standard exchangeable components. It is highly suitable to be used in pharmaceutical, chemical or petrochemical market and in the plastic or oil industry as well. Due to its low NPSH as well as the positive suction head, it is highly suited for pumping of liquefied gasses and liquids under vapor pressure like condensate, refrigerant, boiler feed water . . .
Centrifugal pump / transfer / magnetic-drive / for corrosive fluids - max. 0.7 m³/h | TFS-M7-PP series
Flow rate : max 0.7 m³/h
Operating pressure : max 0.38 Pa
The magnetic drive centrifugal pumps of the trademark Techni-Flow are adapted for the pumping of corrosive and not corrosive acids in different areas:
-...
Operating pressure : max 0.38 Pa
The magnetic drive centrifugal pumps of the trademark Techni-Flow are adapted for the pumping of corrosive and not corrosive acids in different areas:
-...
Centrifugal pump / transfer / magnetic-drive / for corrosive fluids - max. 0.7 m³/h | TFS-M7-PP series
The magnetic drive centrifugal pumps of the trademark Techni-Flow are adapted for the pumping of corrosive and not corrosive acids in different areas:
- surface treatment - return flow of chemical products - water treatment - paper manufacturing - agriculture - food industry - cosmetics - salt water - metallurgy
Amongst others these corrosive liquids can be transferred:
- nitric acid - chlorine water - soap - phosphoric acid
magnetic centrifugal pump
This small pump convinces especially by integrators:
max. flow rate 0,7 m3/h, max. pumping head 3,5 m
- surface treatment - return flow of chemical products - water treatment - paper manufacturing - agriculture - food industry - cosmetics - salt water - metallurgy
Amongst others these corrosive liquids can be transferred:
- nitric acid - chlorine water - soap - phosphoric acid
magnetic centrifugal pump
This small pump convinces especially by integrators:
max. flow rate 0,7 m3/h, max. pumping head 3,5 m
Centrifugal pump / magnetic-drive / plastic - max. 6 m³/h | TFS-M series
Flow rate : max 6.0 m³/h
Operating pressure : max 0.98 bar
This kind of plastic centrifugal pump is flexible...
Operating pressure : max 0.98 bar
This kind of plastic centrifugal pump is flexible...
Centrifugal pump / magnetic-drive / plastic - max. 6 m³/h | TFS-M series
This kind of plastic centrifugal pump is flexible to utilise. The pumping head is high:
The model M70 has a max. flow rate (water) of 6 m3/h, the pumping head is circa 10 m.
The model M70 has a max. flow rate (water) of 6 m3/h, the pumping head is circa 10 m.
Centrifugal pump / circulation / magnetic-drive / acid - max. 20 m³/h
Flow rate : max 20.0 m³/h
Operating pressure : max 1.96 bar
This medium sized centrifugal pump with magnetic coupling convinces by applications which...
Operating pressure : max 1.96 bar
This medium sized centrifugal pump with magnetic coupling convinces by applications which...
Centrifugal pump / circulation / magnetic-drive / acid - max. 20 m³/h
This medium sized centrifugal pump with magnetic coupling convinces by applications which require a high flow rate, for example by the circulation of acid baths or base baths in the surface treatment. Furthermore is this pump ideal for applications in the food industry, for example pumping of nitric acid or natron in CIP/NEP of pipe systems.
Centrifugal pump / magnetic-drive / anti-corrosion - max. 38 m³/h | TF250, TF400
The models TF250 and TF400 are the most powerful magnetic drive centrifugal pumps. They are suitable for...
Centrifugal pump / magnetic-drive / anti-corrosion - max. 38 m³/h | TF250, TF400
The models TF250 and TF400 are the most powerful magnetic drive centrifugal pumps. They are suitable for the filtring of seawater in big aquariums. The pump body made of plastic is therefore very resistant to corrosion.
In the surface treatment industry, mainly by the treating of very toxic wastewater, the pump body requires a high resistance, due to the many different used chemical products.
In the surface treatment industry, mainly by the treating of very toxic wastewater, the pump body requires a high resistance, due to the many different used chemical products.