+7 (812) 645-08-06
Switches: push-button switches, control devices
select brand
Push-button switch - ø 8 - 20.3 mm
These push buttons are directly integrated in the control component one complete component. The job is to send the command quickly and automatically run it in the power...
Push-button switch - ø 8 - 20.3 mm
These push buttons are directly integrated in the control component one complete component. The job is to send the command quickly and automatically run it in the power circuit. The variety of options are seen and configured to fit mounting requirements ranging from 8mm to 20.3mm with different colors with or without illumination. The RAFI Push button mounting hole has 8.1mm diameter. LUMOTAST FK push-button, mounting hole diameter 16.2mm, with flat ribbon cable connection LUMOTAST 25 push-button, mounting hole diameter 16.2mm, collar size 25x25 mm LUMOTAST 75 pushbutton, mounting hole diameter 16.2mm, collar round, rectangular or square, and other options.
Luminous push-button switch - ø 8.1 mm, max. 35 V, 250 mA
This device has suitable design signal lamps with bi-pin t1 socket lamps with...
Luminous push-button switch - ø 8.1 mm, max. 35 V, 250 mA
This device has suitable design signal lamps with bi-pin t1 socket lamps with a maximum of 35 V / 250 mA specifications also having an 8.1 mm diameter measured mounting hole. This device comes in collar type round or square specifically made available to suit any kind of industrial requirement.
Luminous push-button switch - max. 35 V, 100 mA, IP65 | LUMOTAST FK
The RAFI illuminated push button is a quick assembly system that can inserted in front plate , press once , pushbutton is fixed. With a mounting hole of diameter...
Luminous push-button switch - max. 35 V, 100 mA, IP65 | LUMOTAST FK
The RAFI illuminated push button is a quick assembly system that can inserted in front plate , press once , pushbutton is fixed. With a mounting hole of diameter 16.2 mm and a selection of collar type round , square or rectangular. Easy to operate as it is easy to install. Providing optimum performance whenever , wherever the operation demanded while prolonging the service life of any equipment. Less downtime and very time-saving. The illuminating button providing clear indication. Connection reverse polarity protected with clip connector and flat ribbon cable with IDC termination , or with plug-in socket in PCB.
Luminous push-button switch - max. 35 V, 100 mA, IP65 | LUMOTAST 25
These illuminated push buttons are integrated with a lamp socket. It only has 30.7 mm decreased mounting scope integrated with a clip...
Luminous push-button switch - max. 35 V, 100 mA, IP65 | LUMOTAST 25
These illuminated push buttons are integrated with a lamp socket. It only has 30.7 mm decreased mounting scope integrated with a clip connector. It is designed with a 25 x 25 mm collar type square and also has jet security from water that reaches up to IP 65. It is integrated with a connection reverse polarity which is secured with a clip connector and comes with either a flat ribbon cable IDC term termination or with a plug-in socket in PCB. It has a maximum voltage of 35 V or 100 mA and also has 16.2 mm mounting hole diameter.
Luminous push-button switch - max. 35 V, 100 mA, IP65 | LUMOTAST 75
RAFI Gmbh pushbuttons/illuminated pushbutton LUMOTAST 75 with lamp socket has a mounting hole diameter of 16.2 mm and a T4.5...
Luminous push-button switch - max. 35 V, 100 mA, IP65 | LUMOTAST 75
RAFI Gmbh pushbuttons/illuminated pushbutton LUMOTAST 75 with lamp socket has a mounting hole diameter of 16.2 mm and a T4.5 lamp socket. LUMOTAST 75 have round, square or rectangular collar type and can handle maximum 250 V/4 A with contact assignment of maximum 2 NC/2 NO.
LUMOTAST 75 features water jet protection compliant to IP 40 or 65 (LUMOTAST 75 IP 65), a solder terminal, a fixed to front plate with threaded ring, and keyswitches and signal lamps in suitable form.
LUMOTAST 75 features water jet protection compliant to IP 40 or 65 (LUMOTAST 75 IP 65), a solder terminal, a fixed to front plate with threaded ring, and keyswitches and signal lamps in suitable form.
Emergency stop push-button switch - SIL 3, IP 65 | INCA 1
The INCA 1 is an emergency stop device for installation in 22.5mm slot in component...
Emergency stop push-button switch - SIL 3, IP 65 | INCA 1
The INCA 1 is an emergency stop device for installation in 22.5mm slot in component enclosures with two different versions. INCA 1 Tina, designed with electronic adapters for connection to dynamic safety circuits with Vital and Pluto unit connections and also the INCA 1 containing contacts for safer relay connection.
Emergency stop push-button switch - SIL 3
Smile - compact as well as economical E-stop
To be able to satisfy the requirement for a compact as well as effortless to set up E-stop, Smile have been created. The dimensions of the unit tends to make it doable to be mounted...
To be able to satisfy the requirement for a compact as well as effortless to set up E-stop, Smile have been created. The dimensions of the unit tends to make it doable to be mounted...
Emergency stop push-button switch - SIL 3
Smile - compact as well as economical E-stop
To be able to satisfy the requirement for a compact as well as effortless to set up E-stop, Smile have been created. The dimensions of the unit tends to make it doable to be mounted any place you would like. Having M12 link/s or even wire and also centralised installation pockets Smile is extremely simple to set up, particularly over alloy extrusions. Smile is accessible for E-stops both in dynamic and also fixed protection circuits i.e. intended for interfacing overVital/Pluto in addition to
Protection relays. Every model can be obtained in either 1 and also 2 M12 contacts or wire. Within the the surface of the Smile Estop device, Light emitting diodes display the particular condition: Green Means safety is fine, Red Means this particular E-stop have been pushed and when the particular LED will be down the E-stop formerly inside the circuit have been switched on.
To be able to satisfy the requirement for a compact as well as effortless to set up E-stop, Smile have been created. The dimensions of the unit tends to make it doable to be mounted any place you would like. Having M12 link/s or even wire and also centralised installation pockets Smile is extremely simple to set up, particularly over alloy extrusions. Smile is accessible for E-stops both in dynamic and also fixed protection circuits i.e. intended for interfacing overVital/Pluto in addition to
Protection relays. Every model can be obtained in either 1 and also 2 M12 contacts or wire. Within the the surface of the Smile Estop device, Light emitting diodes display the particular condition: Green Means safety is fine, Red Means this particular E-stop have been pushed and when the particular LED will be down the E-stop formerly inside the circuit have been switched on.
Emergency stop push-button switch / with housing - BDF 200 series
Schmersal slender, shock-proof thermoplastic enclosures can be installed ergonomically and fit commercial aluminum...
Emergency stop push-button switch / with housing - BDF 200 series
Schmersal slender, shock-proof thermoplastic enclosures can be installed ergonomically and fit commercial aluminum off-the-shelf units. There are numerous illuminated push buttons, LED indicator lights, selector switches, emergency-stop buttons and key-operated switches available with emergency stop/on/off/reset functionality.
Freely select the push button position, which is labeled with a plastic cover that is easy to read.
Freely select the push button position, which is labeled with a plastic cover that is easy to read.
Push-button switch - DT series
Push button
with concave button
Touch surface 19 x 19
1 Normally open contact (NO)
7 different colours available
with concave button
Touch surface 19 x 19
1 Normally open contact (NO)
7 different colours available
Mushroom push-button switch - Ø 30 mm | NH series
This emergency stop latching push button device is designed with a mushroom...
Mushroom push-button switch - Ø 30 mm | NH series
This emergency stop latching push button device is designed with a mushroom shaped looking plastic push button with a 30 mm diameter with a pull to reset feature that gives a user friendly approach at the same time giving best and efficient results and not to mention its peak durability.
Mushroom push-button switch - PT series
These mushroom push buttons are designed with smooth rounded edges and a 25x25 touch surface. Available in seven colours, these are not latched and has single contact.
Luminous push-button switch - LT series
It has a 19 x 19 touch surface and at it's front, it has a lamp replacement. It also has an illuminated signal that comes with a concave button and it is obtainable in 5 different colour variations.