+7 (812) 645-08-06
Density meters
select brand
In-line X-ray coating weight measurement system - 350 - 600 g/m² | RM 115
Thermo Scientific™ RM 115 Laboratory coating weight gauges are accurate and fast while providing non-contact and non-destructive coating weight measurement of the metal...
In-line X-ray coating weight measurement system - 350 - 600 g/m² | RM 115
Thermo Scientific™ RM 115 Laboratory coating weight gauges are accurate and fast while providing non-contact and non-destructive coating weight measurement of the metal coatings applied to steel strips. The device makes use of proven X-ray fluorescence (XRF) to deliver precise off-line sample measurements, over a wide range of coatings used for similar applications. It performs measurements quickly and easily without the need for time-consuming and expensive chemicals in the analysis. RM 115 is not only reliable and highly efficient, it can easily optimize galvanization processes and save on raw material costs. It also ensures product uniformity and quality.
In-line X-ray coating weight measurement system - 30 - 300 g/m² | RM 300 EC, RM 310 EC
The Thermo Scientific RM 300 EC/RM 310 EC coating weight gauges are attached after the cooling tower in the galvanizing lines in...
In-line X-ray coating weight measurement system - 30 - 300 g/m² | RM 300 EC, RM 310 EC
The Thermo Scientific RM 300 EC/RM 310 EC coating weight gauges are attached after the cooling tower in the galvanizing lines in COLD position. These systems utilize efficient X-ray fluorescence based sensors for the online cross-profile coating weight measurement of almost every type of metal-coated products. They can be used together with the RM 300 EH/RM 310 EH "hot position" gauges and the RM 400 EZ coating weight autocontrol system to create a single complete system for quality control.
In-line X-ray coating weight measurement system - 30 - 300 g/m² | RM 300 EH, RM 310 EH
The Thermo Scientific's RM 300 EH/RM 310 EH belongs to a series of non-tactile coating weight gauges which...
In-line X-ray coating weight measurement system - 30 - 300 g/m² | RM 300 EH, RM 310 EH
The Thermo Scientific's RM 300 EH/RM 310 EH belongs to a series of non-tactile coating weight gauges which analyze and calibrate coil coating, as well as the metallic lines. They greatly enhance overall coating and weight management by means of deducting the lag time between the actual calibrations and the actuator. This results in scrap minimization, and rugged element economy thus providing efficiency.
In-line X-ray coating weight measurement system - 25 - 350 g/m² | RM 315 EC
Thermo Scientific™ RM 315 EC Cold Coating Weight Gauges use X-ray fluorescence...
In-line X-ray coating weight measurement system - 25 - 350 g/m² | RM 315 EC
Thermo Scientific™ RM 315 EC Cold Coating Weight Gauges use X-ray fluorescence (XRF) and near-infrared (NIR) techniques to provide precise, non-contact sensor technology for almost every type of metal coated product. It has a measuring range of 25 to 300 (350) g/m2 per side, depending on the type of alloy.
In-line X-ray coating weight measurement system - RM 400 EZ
Thermo Scientific™ RM 400 EZ coating weight control system complements our full series of coating weight...
In-line X-ray coating weight measurement system - RM 400 EZ
Thermo Scientific™ RM 400 EZ coating weight control system complements our full series of coating weight gauges.
The adaptive coating weight control software provides the highest quality of uniform, precise coating weight cross-profiles and is ideal for hot dip galvanizing lines. It optimizes coating life efficiency and provides significant raw material savings, with a return on investment measured in weeks.
The adaptive coating weight control software provides the highest quality of uniform, precise coating weight cross-profiles and is ideal for hot dip galvanizing lines. It optimizes coating life efficiency and provides significant raw material savings, with a return on investment measured in weeks.
Density monitoring device / concentration / online / for liquids - 0.5 - 2.0 g/cm3 | DM8
The DM8 liquid density analyzer by Yokogawa features a one-touch calibration that comes with a standard calibrating solution. It has outdoor installation for the converter and failure alarm...
Density monitoring device / concentration / online / for liquids - 0.5 - 2.0 g/cm3 | DM8
The DM8 liquid density analyzer by Yokogawa features a one-touch calibration that comes with a standard calibrating solution. It has outdoor installation for the converter and failure alarm display and output. This liquid density analyzer is highly sensible and stable.
It follows the principle of vibration density with a liquid temperature of -10 to 100℃ and an ambient temperature of 10 to 55℃.
This device can withstand pressure of up to 4.9 MPa G with a measuring liquid temperature of 2 MPa G or less. Its power supply can be 90 to 132 V AC or 180 to 264 V AC. Its case is constructed to be dust-proof and rain-proof. The converter weighs approximately 7.7 kg, while the detector weighs 12 kg.
It follows the principle of vibration density with a liquid temperature of -10 to 100℃ and an ambient temperature of 10 to 55℃.
This device can withstand pressure of up to 4.9 MPa G with a measuring liquid temperature of 2 MPa G or less. Its power supply can be 90 to 132 V AC or 180 to 264 V AC. Its case is constructed to be dust-proof and rain-proof. The converter weighs approximately 7.7 kg, while the detector weighs 12 kg.
Laboratory density meter - max. 2 kg, 0.1 mg | VMS2
The VMS2 series allows for dual use with its built-in comparator, for recording density and mass. The tool's 23 million points resolution ensures highly accurate density...
Laboratory density meter - max. 2 kg, 0.1 mg | VMS2
The VMS2 series allows for dual use with its built-in comparator, for recording density and mass. The tool's 23 million points resolution ensures highly accurate density measurements in accordance with OIML R111 hydrostatic comparison A1 & A3. Advanced technology also reduces air bubble formation, which affects buoyancy during measurement. It also has a maximum capacity of 2 kg, and can weight materials up to 65 mm in diameter, and 124 mm in height.
The software packages included with the VMS2 are easily set-up, and come with a fully guided process of measurement for creating detailed measurement reports, including data discrepancies.
The software packages included with the VMS2 are easily set-up, and come with a fully guided process of measurement for creating detailed measurement reports, including data discrepancies.
Laboratory density meter - max. 20 kg, 1 mg | VMS20
You need to know the density of the artifact in order to be able to reduce the physical influence of air buoyancy effects, mass, pressure and force metrology. The new OIML R111-1...
Laboratory density meter - max. 20 kg, 1 mg | VMS20
You need to know the density of the artifact in order to be able to reduce the physical influence of air buoyancy effects, mass, pressure and force metrology. The new OIML R111-1 lays down the density measurement for mass of E class weights for above 330 m and F1 class used at 800 m above sea level.
The VMS solutions uses the built in comparator for mass and density determination. It offers an easy-to-use installation with guided measurement process causing detailed reports of uncertainties.
The density is determined quickly and accurately with the help of it design and measurements methods are applied as per OIML R111 Hydrostatic comparison A1 & A3.
The VMS solutions uses the built in comparator for mass and density determination. It offers an easy-to-use installation with guided measurement process causing detailed reports of uncertainties.
The density is determined quickly and accurately with the help of it design and measurements methods are applied as per OIML R111 Hydrostatic comparison A1 & A3.
Laboratory density meter - max. 20 kg, 5 mg | P20Density
The METTLER-TOLEDO P20Density system determines the density and volume of solid materials, with OIML weights...
Laboratory density meter - max. 20 kg, 5 mg | P20Density
The METTLER-TOLEDO P20Density system determines the density and volume of solid materials, with OIML weights ranging from 2 kg to 20 kg, efficiently, accurately and quickly. The P20Density system meets the standard specifications of the National Institute of Metrology, material manufacturing industries, weights and measures offices for legal weights metrology, and national and industrial calibration laboratories.