Anti-vibration mounts

select brand


Spring damper anti-vibration mount - 12.2155.0122

The GERB spring assembly uses a PUR-sheathing of the steel spring based sordino damping in order to nullify natural oscillations and are well suited for the insulation of a variety of machines and systems, while...

Spring damper anti-vibration mount - 12.2155.0122

The GERB spring assembly uses a PUR-sheathing of the steel spring based sordino damping in order to nullify natural oscillations and are well suited for the insulation of a variety of machines and systems, while being completely unaffected by spray water. Installation procedure involve the removal of threaded pins that block the ventilation drill holes, before start up. These units are provided with fabric construction mats that can prevent slipping of equipment even without the added anchoring bolts in cases where the equipment is exposed to horizontal forces. The specifications of these elements are based on the frequency ratio and dynamic forces with maximum load values that are valid only in static conditions. These models also include versions without damping as well as those with omni directional VISCO-damping.

Spring damper anti-vibration mount - 12.2155.0321

The GERB spring assembly S3Q sordino dampe Type S3Q-241 S from APSOparts is designed with a PUR-sheathing that stops natural oscillations from taking place. The components within this unit deliver linear spring rates and operate on...

Spring damper anti-vibration mount - 12.2155.0321

The GERB spring assembly S3Q sordino dampe Type S3Q-241 S from APSOparts is designed with a PUR-sheathing that stops natural oscillations from taking place. The components within this unit deliver linear spring rates and operate on low natural frequencies.

These spray water-insensitive spring assemblies are best used for insulating oscillation within machines and systems. Designed with lacquered cast iron, this unit comes with two fabric construction mats that allow convenient installation on machines, eliminating the need for anchoring bolts.

Threaded pins must be removed from the ventilation drill holes before initial use.

The components are designed with set dynamic forces and a set frequency ratio. The optimal static load can be determined by its load capacity Fz.

This unit may also be supplemented with omni directional VISCO-damping or undamped upon request.

Spring damper anti-vibration mount - 12.2155.3121

The APSO parts GERB D1 has a case constructed from lacquered cast iron.
The PUR-sheathing of the steel spring-based sordino dumping is meant to prevent natural vibrations. The elements integrated in it have linear spring rates and very...

Spring damper anti-vibration mount - 12.2155.3121

The APSO parts GERB D1 has a case constructed from lacquered cast iron.
The PUR-sheathing of the steel spring-based sordino dumping is meant to prevent natural vibrations. The elements integrated in it have linear spring rates and very low natural frequencies. This spring assembly is ideal for oscillation insulation of all kinds of machines and machine systems. It is also tolerant to spray water.
The assembly requires removal of the threaded pins which block the ventilation drill holes, which must be done before start up. A slip-free installation even in the horizontal load-bearing position is made possible without the need to add anchoring bolts by using the two supplied mats of fabric construction.
The load capacity specified is meant for static load. All the elements meet specifications for dynamic forces and the frequency ratio. There are also special versions for multi-directional VISCO damping or without damping as well.

Air spring anti-vibration mount - 12.2122.0001

The APSOvib air spring is made of black CR steel cores in its elastomer parts. Its screw is made of 8.8 galvanized steel and its base plate is made of SLM 1A up to 12A in aluminium form and...

Air spring anti-vibration mount - 12.2122.0001

The APSOvib air spring is made of black CR steel cores in its elastomer parts. Its screw is made of 8.8 galvanized steel and its base plate is made of SLM 1A up to 12A in aluminium form and SLM 24A up to 1924 in galvanized steel form. This device can be used in the active insulation of ventilators and compressors as well as the passive insulation of gauges and scales. The air spring is positioned on the elastomer body supported by the steel ring thus providing the insulation of oscillation. The frequency ratio and dynamic force are primary elements for the operation of the system. The frequency is achieved through 3 and 5 Hz depending on the work load and height. The object cane positioned has a height range of 65 and 90 mm.
GAMM

Type A anti-vibration mount - ACMM

Diameter : 10 mm - 100 mm

Type A anti-vibration mount - ACMM

Diameter : 10 mm - 100 mm

CONTITECH

Anti-vibration mount

Driver´s Cabs for Industrial Vibration Control comprise a flexible mounting technique which enables high endurance to operations with...

Anti-vibration mount

Driver´s Cabs for Industrial Vibration Control comprise a flexible mounting technique which enables high endurance to operations with...

Anti-vibration engine mount - V series

An improved level of ride convenience can be attained by efficiently isolating the engine...

Anti-vibration engine mount - V series

An improved level of ride convenience can be attained by efficiently isolating the engine...

Air spring anti-vibration mount - 0.5 - 440 kN

The ConiTEch Air Spring Systems provides solutions for mounting vibration-oriented machines....

Air spring anti-vibration mount - 0.5 - 440 kN

The ConiTEch Air Spring Systems provides solutions for mounting vibration-oriented machines. It can hold loads ranging from 0.5 kN up to 440 kN and function in minimum frequency of 0.5 up to 3.5 Hz based on the type. This air isolator tool is also beneficial for sensitive measuring tools and holding large supports with uniform single system properties.

Rubber anti-vibration mount / metal bonding - SCHWINGMETALL®, ROTAFRIX®

The product range of ContiTech SCHWINGMETALL® is mostly made of premium rubbers and metals to assure high endurance capability of the product. It has...

Rubber anti-vibration mount / metal bonding - SCHWINGMETALL®, ROTAFRIX®

The product range of ContiTech SCHWINGMETALL® is mostly made of premium rubbers and metals to assure high endurance capability of the product. It has...
{{item.name}}