Manual positioning stages

select brand


GRUNDFOS

Disinfection system : chlorine gas, chlorine dioxide - 5 - 60 g/h | OCD-162 Oxiperm Pro series

The Oxiperm Pro OCD-162 systems can produce chlorine dioxide, an efficient disinfectant. It can generate chlorine dioxide by using diluted solutions of sodium chlorite (NaClO2, 7.5%) and hydrochloric acid...

Disinfection system : chlorine gas, chlorine dioxide - 5 - 60 g/h | OCD-162 Oxiperm Pro series

The Oxiperm Pro OCD-162 systems can produce chlorine dioxide, an efficient disinfectant. It can generate chlorine dioxide by using diluted solutions of sodium chlorite (NaClO2, 7.5%) and hydrochloric acid...
Misumi Europa GmbH OWIS

Single shaft linear stage / manual - 25 - 150 mm | LT 60 series

Manufactured by Owis, the Precision Linear Stages LT 60 are cost-efficient linear stages that are suitable for both R&D and industrial applications. The Precision...

Single shaft linear stage / manual - 25 - 150 mm | LT 60 series

Manufactured by Owis, the Precision Linear Stages LT 60 are cost-efficient linear stages that are suitable for both R&D and industrial applications. The Precision Linear Stages LT 60 allow a motion that is slip-stick free through their unique guidance and a long life time through their material combination of spindle and nut.

The key features of the Precision Linear Stages LT 60 include a variety of travel rate ranging from 25 mm, 50 mm, 75 mm, 100 mm to 150 mm, a deformation-resistant aluminum, stainless recirculating ball bearing guides, a fixing device for the slide, and an additional non-magnetic version.

Single shaft linear stage / manual - 90 - 400 mm | LT 120 series

The Linear Precision Stages LT 120 is a cost-effective guiding device ideal for use with industrial applications and in research and development. This device utilizes a special guidance system...

Single shaft linear stage / manual - 90 - 400 mm | LT 120 series

The Linear Precision Stages LT 120 is a cost-effective guiding device ideal for use with industrial applications and in research and development. This device utilizes a special guidance system that ensures virtually slip-stick free motions in addition to the ability to handle high loads. All the aluminum components are coated with a high-quality black anodized, while the material combination of the nut and the spindle results in very low wear and tear and an extended lifespan.

The measurements for the travel are 90mm, 140mm, 240mm, 300mm or 400mm, and the carriage is fitted with stainless steel recirculating ball bearing guides. Operators can adjust the clamping element breaking force to the complete fixing of the fine-thread spindle.

Single shaft linear stage / manual - 50 - 150 mm | LPT 30 series

OWIS LPT 30 linear precision stages have a 30 mm width and 16 mm working height. The compact devices have width and shallowness lower than a matchbox, yet can handle loads of 100 N. Travel options available are...

Single shaft linear stage / manual - 50 - 150 mm | LPT 30 series

OWIS LPT 30 linear precision stages have a 30 mm width and 16 mm working height. The compact devices have width and shallowness lower than a matchbox, yet can handle loads of 100 N. Travel options available are 50 mm, 100 mm and 150 mm.

The rotating knob makes it easier to handle the fixing device. This allows fixing of the position at the spindle. All the aluminium parts in LPT 30 feature a superior black anodized coating for protection. The aluminium is resistant to deformation.

LPT 30 features a fine-thread screws with precise spindle offering minimal backlash. The stages have carriage with ground. Also available are ball bearing guides which are recirculating and stainless. To enable fixing of the adjusted position, fixing device is possible.

LPT 30 allows XY, XZ or XYZ assemblies.

Single shaft linear stage / manual - 75 - 300 mm | LT 80 series

The economically priced linear stages of the series LT 80 are the appropriate choice for both R&D and industrial applications.

The special guidance provides a virtually slip-stick free motion as well as a high load capacity. The material combination...

Single shaft linear stage / manual - 75 - 300 mm | LT 80 series

The economically priced linear stages of the series LT 80 are the appropriate choice for both R&D and industrial applications.

The special guidance provides a virtually slip-stick free motion as well as a high load capacity. The material combination of spindle and nut ensures low wear and tear as well as long life time.

It is possible to sensitively adjust the breaking force of the clamping element up to the complete fixing of the fine-thread spindle without displacing the spindle.

All aluminium parts have a top-quality black anodized protective coating.

travel 75 mm, 100 mm, 150 mm, 200 mm or 300 mm

designed for industrial applications

deformation-resistant aluminium

reflection-poor, black anodized

ground fine-thread spindle with low backlash

carriage with ground and stainless recirculating ball bearing guides

fixing device for the slide

XY, XZ or XYZ mounting possible

Manual positioning table - max. 5 mm, ø 4.8 mm | MT 30 series

This series of products features items that come with proven measuring stages, as well as a compact design and compatibility with a broad range of industrial and R&D applications....

Manual positioning table - max. 5 mm, ø 4.8 mm | MT 30 series

This series of products features items that come with proven measuring stages, as well as a compact design and compatibility with a broad range of industrial and R&D applications. In addition to allowing space saving, the positioning is high precision, while the components are small. Next, the M6 center holes come with an aperture of 4.8mm, while the products can be used for micro-optical applications, along with mounting of the MT 30 stages.

The aluminum parts come with top-quality black anodized protective coating, as well as a measuring range of 5mm. Other important features are the compact design, as well as the deformation resistant aluminum and preloaded linear ball bearing guides.
{{item.name}}