Taps, dies and thread milling cutters

select brand


OSG

High-performance tap - M, MF, UNC , UNF / A-SFT A-POT

A-TAP Series is deigned to tackle any material, any application and any given time. Fact is that almost all tapping...

High-performance tap - M, MF, UNC , UNF / A-SFT A-POT

A-TAP Series is deigned to tackle any material, any application and any given time. Fact is that almost all tapping problems are initiated by unstable chip evacuation. The A-Tap Series by OSG is designed to solve these problems and can be used for a wide spectrum of machining conditions and work materials. The A-Tap Series by OSG delivers superior chip evacuation to enable lowered processing costs, reduced tool management costs and peace of mind.

Roll form tap - M3 - M6 | R-XPF series

The Revolution X-Performer Forming Taps enhances tool life using a V coating which...

Roll form tap - M3 - M6 | R-XPF series

The Revolution X-Performer Forming Taps enhances tool life using a V coating which allows forming in the steel, metal sheet, carbon steels and even on alloy steels. It is a very cost-effective solution since it reduces low wear. It provides high productivity due to its excellent capacity using advanced technology.

Long-shank tap - M2 - M20 | CC-LT-POT, series

These are taps that are available with longer...

Long-shank tap - M2 - M20 | CC-LT-POT, series

These are taps that are available with longer reach. It can have total length of about 200 mm. These taps make it possible for tapping those places that were not reachable before.

Machine tap - M3 - M30 | S-XPF series

This complete series of forming taps provides excellent performance when tapping...

Machine tap - M3 - M30 | S-XPF series

This complete series of forming taps provides excellent performance when tapping hardened steels, forged steels and alloy steels that have a hardness up to 35 HRC. The forming taps are available either with or without coolant. Designed by OSG, these wear resistant forming taps can withstand tolerances of 6GX and 7GX.

Stainless steel tap - M2 - M30 | CC series

OSG's CC or Control Chip series is a range of taps that are designed specifically for stainless steel. These...

Stainless steel tap - M2 - M30 | CC series

OSG's CC or Control Chip series is a range of taps that are designed specifically for stainless steel. These...

Machine tap - 065410

Thread type x nominal diameter x pitch M10xl5
Core...

Machine tap - 065410

Thread type x nominal diameter x pitch M10xl5
Core hole diameter 8.5 mm
Thread length (metric thread) 20 mm
Length 100 mm
Shank diameter 10.0 mm
Square size 8.0 mm
Dormer Tools

Threading die

This die is ideal for use in applications that require an external threading. Made of chromium...

Threading die

This die is ideal for use in applications that require an external threading. Made of chromium steel, thus making it suitable for use in manual threading operations.

A solid die has the capacity to cut more precisely than a split die, but a solid die may be split. Chromium steel has a lower red hardness than high speed steel.

Threading tool

There are four primary tap geometries and tapping processes supported by Dormers threading range:

Straight Flute Taps: the most commonly used type of tap. Suitable for blind or though hole thread production in most materials, mainly...

Threading tool

There are four primary tap geometries and tapping processes supported by Dormers threading range:

Straight Flute Taps: the most commonly used type of tap. Suitable for blind or though hole thread production in most materials, mainly steel and cast.

Spiral Point Taps: features a straight, fairly shallow flute and is also referred to as a gun nose or spiral point tap. The point is designed to drive the swarf forward, hence this type of tap is recommended for threading through holes.

Spiral Flute Taps: intended primarily for threading blind holes, the helical flute transports swarf back out of the hole, thus avoiding packing of swarf in the flutes or at the bottom of the hole.

Forming Taps: forming taps differ from cutting taps in that the thread is produced by deformation of the component material, rather than the traditional cutting action. This means that no swarf is produced and the resultant thread is stronger.

Dormer also offers a range of split (adjustable) and solid dies for the production of external screw threads.
{{item.name}}