+7 (812) 645-08-06
Fiber optic signal processing
select brand
Fiber optic amplifier / dual-display - 0.2 - 5 ms | DF-G1
This dual-display fiber amplifier has the latest mechanical design and a 32-bit microprocessor with a 12-bit ADC for a simple set-up and configuration, stable performance, and economical pricing, with an intuitive...
Fiber optic amplifier / dual-display - 0.2 - 5 ms | DF-G1
This dual-display fiber amplifier has the latest mechanical design and a 32-bit microprocessor with a 12-bit ADC for a simple set-up and configuration, stable performance, and economical pricing, with an intuitive user interface. It shows the signal level and threshold at the same time.
Superior gain and threshold are ensured for all applications, including those low contrast ones. Its user can control all operating parameters like switch point threshold, light operate or dark operate, output timing functions, gain level and response speed.
To minimize warm-up drift and to reduce the effect of side-by-side mounting of multiple fiber amplifiers, it has thermally stable electronics including a cross-talk avoidance algorithm. It has fast response (20 milliseconds) with ECO display mode saving power by 25%.
Superior gain and threshold are ensured for all applications, including those low contrast ones. Its user can control all operating parameters like switch point threshold, light operate or dark operate, output timing functions, gain level and response speed.
To minimize warm-up drift and to reduce the effect of side-by-side mounting of multiple fiber amplifiers, it has thermally stable electronics including a cross-talk avoidance algorithm. It has fast response (20 milliseconds) with ECO display mode saving power by 25%.
Fiber optic amplifier - 0.2 - 0.5 ms | D10 series
The measured value and the setting value can be viewed simultaneously. D10 presents advanced fiber optic amplifier for use with plastic fibers. These films exhibit...
Fiber optic amplifier - 0.2 - 0.5 ms | D10 series
The measured value and the setting value can be viewed simultaneously. D10 presents advanced fiber optic amplifier for use with plastic fibers. These films exhibit birefringence, which can prevent stable detection in conventional photoelectric sensors. With push button programming or manual gain adjustment and available with visible red or green sensing beam. In addition, the sensitivity can be easily fine tuned with a touch of a button. Superb device that provides light or dark process operation. Manufactured for numeric or bargraph display on expert models and as thin as 10 mm housing which goes with standard 35 mm DIN-rail mounting.
Fiber optic amplifier - 0.05 - 0.5 µs | D12 series
Offers Light emitting diode bargraph to point out transmission power, detecting contrast, encoding condition as well as analytical alerts, if not within high-speed...
Fiber optic amplifier - 0.05 - 0.5 µs | D12 series
Offers Light emitting diode bargraph to point out transmission power, detecting contrast, encoding condition as well as analytical alerts, if not within high-speed setting
Obtainable in glass as well as plastic-type fiber optic designs
Consists of minor gain gauge having alert yield
Resolves routine purposes having affordable conventional designs
Offers high-speed detecting response and better detecting strength in certain designs
Performs exceptionally well within low-contrast uses having ac-coupled designs
Offers effortless push-button TEACH-mode set-up over D12E Professional designs
Obtainable in glass as well as plastic-type fiber optic designs
Consists of minor gain gauge having alert yield
Resolves routine purposes having affordable conventional designs
Offers high-speed detecting response and better detecting strength in certain designs
Performs exceptionally well within low-contrast uses having ac-coupled designs
Offers effortless push-button TEACH-mode set-up over D12E Professional designs
Fiber optic amplifier / compact - 0.5 ms | FI22 Expert series
Features a low-profile IP67-sealed housing for inconspicuous machine surface mounting (no enclosure required)
Includes 8-segment LED light...
Includes 8-segment LED light...
Fiber optic amplifier / compact - 0.5 ms | FI22 Expert series
Features a low-profile IP67-sealed housing for inconspicuous machine surface mounting (no enclosure required)
Includes 8-segment LED light bar to indicate relative received signal strength, sensing contrast, programming status and diagnostic warnings
Offers TEACH-mode programming for static, dynamic and single-point configuration, and manual adjustment for fine tuning
Features easy-to-read TEACH and signal strength readout, as well as a continuous readout of operating status
Can be programmed for either light- or dark-operate output
Includes 8-segment LED light bar to indicate relative received signal strength, sensing contrast, programming status and diagnostic warnings
Offers TEACH-mode programming for static, dynamic and single-point configuration, and manual adjustment for fine tuning
Features easy-to-read TEACH and signal strength readout, as well as a continuous readout of operating status
Can be programmed for either light- or dark-operate output
Fiber optic amplifier - 500 Hz, max. 300 mm | LV461 series
This revolutionary series has been specially designed to conform with all the basic...
Fiber optic amplifier - 500 Hz, max. 300 mm | LV461 series
This revolutionary series has been specially designed to conform with all the basic prerequisites including a 20-turn potentiometer that ensures high resolution sensitivity adjustments. It is also equipped with two switches for both light and dark switching as well as for choosing between a larger range or higher switching frequency.
Fiber optic amplifier - 500 Hz, max. 525 mm | LV462 series
The series with 3-digit display enables the display of switching threshold....
Fiber optic amplifier - 500 Hz, max. 525 mm | LV462 series
The series with 3-digit display enables the display of switching threshold. The device features auto set function or manual function with + - button. A switch is included for light/dark switching, simple menu functions enables to set the range and various timing of the device.
Fiber optic amplifier - 2 500 Hz, max. 525 mm | LV463 series
The LV463 fiber optic sensor is made with a strong...
Fiber optic amplifier - 2 500 Hz, max. 525 mm | LV463 series
The LV463 fiber optic sensor is made with a strong performance rate to make it work in many fields and functions. This can work with many easy to read displays for making configurations easy to handle.
Fiber optic amplifier - 1 500 Hz, max. 300 mm | LVS 325 series
"Teach-in" is most commonly used to calibrate a series of fiber optic cable...
Fiber optic amplifier - 1 500 Hz, max. 300 mm | LVS 325 series
"Teach-in" is most commonly used to calibrate a series of fiber optic cable...
Fiber optic collimator
This product features an optical system designed for collimation of laser light as well as for transmission fiber coupling of collimated laser...
Fiber optic collimator
This product features an optical system designed for collimation of laser light as well as for transmission fiber coupling of collimated laser light. It can be utilized for various applications like industrial laser technology and industrial image processing. The product is made of anodized aluminum or stainless steel housing. It also contains either an optical glass or silica lenses that comes with an optional AR-coating or GRIN lenses. It's being connected by standard SMA fiber optics and boasts single axis adjustment within the optical axis.
Fiber optic separator - 1 x N, 2 x N
You are looking at a brand new series of multimode splitters, based on waveguides that are planar integrated and are produced by ion exchange means...
Fiber optic separator - 1 x N, 2 x N
You are looking at a brand new series of multimode splitters, based on waveguides that are planar integrated and are produced by ion exchange means at the glass levels. In terms of the components of this device, you should know that these are based on lithographically patterned waveguides.
This is the main reason the design of this product is such a compact one, and will save you plenty of space in the long run. The diameter of the waveguides start from 50im and extend up to 200im. In terms of the number of output and input channels, this is up to 32.
This is the main reason the design of this product is such a compact one, and will save you plenty of space in the long run. The diameter of the waveguides start from 50im and extend up to 200im. In terms of the number of output and input channels, this is up to 32.
Fiber optic separator - 1x2, 1x4, 1x8, 1x16, 1×32, 1×64
If you are looking for an optimum balance-cost performance, then this is one of the products...
Fiber optic separator - 1x2, 1x4, 1x8, 1x16, 1×32, 1×64
If you are looking for an optimum balance-cost performance, then this is one of the products you should consider investing in. In addition to the intelligent design, and the in-house manufacturing methods of a really high quality, these splitters are also reliable and suitable for applications that must be ran under harsh environmental conditions.